BN207/MN505 Local Area Network Management Assignment 1, TP1 2013 Information Technology MN505 Local Area Network Management Assignment 1, Trimester 2, 2016 Assignment 1: Individual Assignment Submission Due: Week 6, (Melbourne: Friday, 25 August 2016, 5:00 PM) (Sydney: Week6 time as per Sydney Lecturer) Total Marks = 20 (10% of total assessment) Purpose of the assessment: The purpose of this assignment is to allow the students to demonstrate their excellence over the commands of a CISCO Router and a Switch. The students are required to exercise and enhance their ability to critically think and deeply understand, practise, and utilise a CISCO Router and a Switch commands; and they are required to write a technical report by reflecting their deep understanding of the technical details. Description of the assessment: The assessment contains Part 1 and Part 2 as detailed below. PART 1: (10 marks) In this assignment you are required to use CISCO router, Switch, and PCs in NetSim, and write commands for the following questions. Demonstrate any two commands nominated by your tutor during your week6-lab time. Questions include: 1. What the activities performed with line command? 2. What command is used to delete the configuration stored in NVRAM? 3. What command is used to set a user-mode password for the console port? 4. What command is used to set the enable secret password to cisco? 5. What commands are used to reinitialise the router and totally replace the running-config with the current startup-config? 6. What activities are performed with config t? 7. Explain the following commands a. debug b. access-list c. copy run start d. terminal no editing e. logging synchronous f. description g. bandwidth 64 h. line aux 0 i. exec-timeout 0 0 j. loginMN507 Local Area Network Management Page 2 of 4 PART 2: (10 marks) Using NetSim, write a report on Cisco commands to set up the following network:  2 PCs (PC1 & PC2) are connected to a Switch A.  2 PCs (PC3 & PC4) are connected to Switch B.  1 PC is connected to a Hub A.  1 Server is connected to a Hub B  Switch A is connected to Router (R1) through Fast Ethernet interface.  Switch B is connected to Router (R2) through Fast Ethernet interface.  The Hub A is connected to Router (R3) through Fast Ethernet interface.  The Hub B is connected to Router (R4) through Fast Ethernet interface.  The four routers are connected to each other through serial interfaces.  1 PC (PC0) is used as a console and connected to R1 console port.  Assign an IP address to each of the PCs, and routers' interfaces. a. Answer the following questions: i. How many Broadcast domains, and how many collision domains are in this network? ii. What type of cables are used between the following devices: 1. PC1 and Switch A. 2. The Hub and R3. 3. PC0 and R1. b. From PC0, go to Desktop tab, and then choose Terminal to access R1 through the console port. From R1 prompt, ping all other PCs and the server to check connectivity with each of them. c. For each of the routers and switches, configure the following parameters: i. Hostname. ii. Description to all routers interfaces. iii. Banners to Server and PC2 iv. All passwords (Enable, Secret, Console, Aux and vty). Criteria for assessment: Your assignment should be completed according to the General Guidelines for Presentation of Academic Work.  successful completion of required tasks  quality of figure - comments - meaningful names  accompanying documentation including - table of contents and page numbers - a front page - indicating your name, a statement of what has been completed and acknowledgement of the names of all people (including other students and people outside of the university) who have assisted you. - list of references used (IEEE style).MN507 Local Area Network Management Page 3 of 4 Submission guidelines: 1. Your report should include the following:  The cover page must identify student (name and number), teaching staff, and assignment.  The assignment must use 12 point font size minimum and at least single line spacing with appropriate section headings.  Reference sources must be cited in the text of the report, and listed appropriately at the end in a reference list. 2. The assignment must be submitted in soft (electronic) copy under Moodle. Marking criteria: Marks are allocated as follows: Section to be included in the report Description of the section Marks Introduction Outline of the report ( in 2 sentences) 1 Identification Description of the report 1 Part-1 Demonstrate Commands; and take screenshots along with the date and time (lower right of your computer); and organise the screenshots to prepare a clearly organised comprehensive 1000-word report 4+4 Part-2 Network design and screenshot based clearly organised comprehensive 1500-word report. 4+4 Reference style IEEE format 2 Poor writing Inadequate structure, careless presentation, or the report exceeds the word limit by more or less than 10% -2 Total 20 Extensions: Requests for an extension, accompanied by supporting documentation, must be received by the student in writing before 3 working days from the due date else penalties may apply for late submission without an approved extension. Special consideration form is available on level 7 reception. Plagiarism: Depending on the seriousness of the case, penalties can vary from a written warning or zero marks to exclusion from the course or rescinding the degree. Students should make themselves familiar with the full policy and procedure available at: http://www.mit.edu.au/about-mit/institute-publications/policies-procedures-andguidelines/Plagiarism-Academic-Misconduct-Policy-ProcedureMN507 Local Area Network Management Page 4 of 4 Marking Rubric for Assignment #: Total Marks (20) Student Name: Student Id: Submission Due: …./…../2016 Date Submitted:…../…../ 2016 Marker's Name: Mark Achieved: /20 Grade Mark HD 18-20 D 15-17 C 12-14 P 9-11 Fail <9 Excellent Very Good Good Satisfactory Unsatisfacto ry Introduction /1 All topics are pertinent and covered in depth. Ability to think critically and source material is demonstrated Topics are relevant and soundly analysed. Generally relevant and analysed. Some relevance and briefly presented. This is not relevant to the assignment topic. Identification /1 Complete and comprehensive description Good description presented Acceptable description presented Poor description presented Very poor or No description presented Part-1 /4+4 Clear screenshots are from the environment used; and clear consistent presentations of the commands exist with potential details. Clarity and consistency and details are to a greater extent. Clarity and consistency and details are to a great extent. Clarity and consistency and details are to some extent. Clarity and consistency and details are absent and unclear. Part-2 /4+4 All elements are present and very well integrated. Component s present with good cohesive Components present and mostly well integrated Most components present Proposal lacks structure. Reference style /2 Clear style switch excellent source of references. Clear referencing style Generally good referencing style Sometimes clear referencing style Lacks consistency with many errors Poor writing Inadequate structure, careless presentation, or the report exceeds the word limit by more or less than 10% -2